THE FOUNDATION OF PLUMBING SKILLS FOR BATHTUB INSTALLATION

The Foundation of Plumbing Skills for Bathtub Installation

The Foundation of Plumbing Skills for Bathtub Installation

Blog Article

Book Appointment

What are your ideas regarding How to Install a Bathtub?


A Step-by-Step Guide to Installing a Bathtub
Setting up a tub isn't specifically rocket science, however it does require strong plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a brand-new one is additionally a reasonably difficult project. If the old bathtub is readily accessible, the project can relocate quickly; if you have to open a wall to remove the old bathtub and also place the brand-new tub, the task is much harder. In either instance, the task is within a residence handyman's skills, although you will require a helper to move out the old tub and set in the new one. Make sure you have certified yourself for the job and also are comfortable attempting it. As opposed to employing a professional to take over a halfway-completed task, it is much better to take into consideration utilizing one before you begin. Opportunities are you might need an expert plumber to make tube links.
This write-up will assist you mount a new bath tub in your restroom if you have currently bought a new tub and also do not need to change the setup of your previous water supply pipes.
Your devices and product checklist must comprise the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you need to replace old taps with new ones as a part of your installation, then the first thing you must do is separate the water. After doing so, activate the faucets to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be rather problematic because of the restricted access that is frequently the situation.
    Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the faucets. Have a towel ready for the staying water that will originate from the pipes. Once the supply pipelines have actually been eliminated, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from transforming during this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any kind of old sealing substance.
    Prior to moving on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will need a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and also the various other end supplies a link to the existent supply pipelines.
    If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
    Next off, place the tap in the placing opening in the bath/basin making sure that the washing machines remain in location between the tap and the sink. Safeguard the tap in position with the supplier supplied backnut. As soon as the tap is safely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap adapters. The former type needs to be linked to the tap ends first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.

    Setting up the Bath tub


    Utilizing both wood boards under its feet, put the bathtub in the needed placement. The wooden boards are practical in equally spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny factors.
    The following goal is to make sure that the bathtub is leveled all round. This can be achieved by checking the level as well as readjusting the feet on the bath tub until the level reads level.
    To set up faucets, fit all-time low of the outermost versatile tap port to the proper supply pipe by making a compression sign up with; then do the very same for the other tap.
    Switch on the water system and also check all joints and brand-new pipework for leakages as well as tighten them if essential. Load the bath tub as well as also inspect the overflow electrical outlet and also the regular outlet for leakages.
    Ultimately, repair the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bath tub should wait till the bath tub has been utilized a minimum of once as this will settle it right into its last position.

    Planning for the Installation


    First of all, the sustaining structure provided with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets system to prevent stress on the bath tub.
    Fit the versatile tap connectors to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet with the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you utilize all of the supplied washers.
    Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must now prepare to be suited its last placement.

    Tiling Around the Tub


    In the area where the bath fulfills the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to split an inflexible seal, triggering the water to penetrate the wall surface between the bath and the tiling, causing complications with dampness and feasible leakages to the ceiling below.
    You can select from a variety of coloured sealers to blend in your components and also fittings. They are offered in tubes and cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always fill the bathtub with water prior to sealing, to allow for the movement experienced when the tub remains in use. The sealant can crack relatively early if you do not consider this motion before sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise easily offered on the marketplace. It is a good idea to fit the ceramic tiles using water-resistant or waterproof sticky and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    Do you appreciate more info about Installing A Bathtub? Post a remark further down. We would be glad to know your reactions about this entry. We hope that you come back again later on. For those who liked our article kindly make sure you remember to share it. Kudos for your time. Don't forget to pay a visit to our site back soon.


    Free Quote

    Report this page